*Patents Pending
www.nemoequipment.com
NEMO EQUIPMENT INC.
100 Factory Street, Nashua, NH 03060
Phone: 1-800-997-9301
OVERVIEW
1. PU Weather Check Window
2. Door Tie-backs
3. Rear Scoop Style Vent
4. Removable Internal Airbeams
5. Rear Pump Access Zipper
6. Internally Deployable Side Vent
7. Multiple Guy-out Points
8. Front Pump Access Zipper
9. Mesh Door With Two Entry Options
10. ExoFly™ Retractable Vestibule
SET UP
Lay out the contents of Morpho AR™ and make sure you received your
tent and the following: stuff sack, Nemoid™ Foot Pump, 2 replacement
bladders with inflate/deflate valve, 8 stakes, guy lines, and repair kit.
Also confirm that you received any optional items you may have
ordered including: Footprint, T-shirts, or accessories.
1
To take Morpho AR™ down, first remove all gear and as much moisture
as possible. Water will add weight to your pack and can lead to mildew.
1
Begin by placing the deflator caps on the inflate/deflate valves. When
properly connected, there will be an audible click. The airbeams will
immediately begin to deflate.
2
Roll the tent along the airbeams towards their valves to force out all the
air. Try to clean as much dirt and debris from your tent as possible
before packing it. This will help preserve the breathability of the tent
fabrics and reduce overall wear and tear.
3
TAKE DOWN
Morpho AR™
1
4
2 5
1. Nemoid™ Foot Pump Body
2. Dump-Check Valve™
3. Neoprene hose
4. Quick-Disconnect Valve
5. Deflator Cap
6. Velcro Straps for Attachment Inside Tent Shell
7. Bladder Access Pocket
8. Hypalon® Valve Reinforcement
9. Velcro Panels for Securing Airbeam Ends
10. Protective Cap for Valve
11. Quick-Disconnect Inflate/Deflate Valve
6
11
8
10
7
Integrated Pump and Airbeam
In a flat area, begin the setup of your tent by staking it out.
2
3
4
The first time you set up Morpho AR™, you will need to attach the
airbeams. Making sure the long beam is in front and the short beam is in
the rear of the tent, line up and attach the Velcro straps on airbeams to
the tent. This can be done with beams inflated or deflated. Adjust the
Velcro so there is no puckering of the tent shell. Keep your airbeams
attached to the tent to save setup time in the future.
Disconnect the deflator cap and connect your Nemoid™ Foot Pump to
one of the airbeams. When properly connected, the quick-disconnect
fittings will make an audible click. When inflating from outside the tent,
pass the end of the pump through the pump access zippers.
5
1
3
4
Step on pump body repeatedly until it becomes difficult to add air.
Disconnect pump and repeat process with second airbeam.
5
Stuff the tent entirely into the stuff sack. By starting with the back end
of Morpho AR™ you will avoid trapping air in your stuff sack.
4
Fold the top edge of the stuff sack down several times to make an
air-tight seal. Allow excess air to escape while compressing. Secure the
stuff sack with the compression straps on both sides.
5
Remember to leave no trace. Before leaving your campsite take a
thorough look around making sure you have not left anything behind,
out of place, or damaged.
6
2
9
3
2
5
5
1
2
3
4
10
7
8
9
6
5
©2007 NEMO Equipment, Inc.
MORPHO AR
™
(9 pagine)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale